https://www.miningweekly.com

Company develops dust suppressants to assist miners

1st April 2022

     

Font size: - +

Leading fine particle specialist Reynolds Soil Technologies (RST Solutions) is assisting mine-site operators to comply with tougher workplace exposure standards for airborne contaminants.

In Australia, the national regulator for occupational health and safety, Workplace Health and Safety, halved the occupational exposure limits (OEL) for silica dust to 0.05 mg/m³ and reduced the OEL for other mineral dust from 2.5 mg/m³ to 1.5 mg/m³.

With spray and foaming systems being the most common methods for suppressing mineral dust, RST Solutions is advising companies along the material supply chain against boosting the dosage levels of surface-active agents commonly used in these applications.

Typically, dust suppression methods involve a surface-active agent added to water that is applied to the bulk material through spray or foaming systems to lift the dust extinction moisture levels.

While regular dust control formulas contain chemical elements considered low enough at application strength to not cause any problems, increasing the amount applied to meet strict dust exposure limits is not an acceptable solution, says RST Solutions operations and technical director David Handel.

“It is critical for dust control specialists using a spray or foaming suppression solution during mining, transportation and at storage facilities to understand the chemistry being used downstream to maintain product quality and prevent potential adverse chemical reaction during processing and manufacturing,” says Handel.

“Dust control specialists need to look at how dust suppression additives can add value to improve downstream operation, not undermine end-user processes by altering the product’s chemistry and devaluing quality.”

In response to issues raised by processing plants about some dust suppression agents affecting product quality, RST Solutions’ research and development (R&D) team has been developing high-functioning formulas that preserve mineral properties for processing.

The chemistry is tailormade to suit the mined material, various dust control application methods and downstream processes to provide a higher level of dust control efficiency along the whole material supply chain while remaining compatible with end-user expectations.

Without revealing the composition of RST Solutions’ technology, Handel says the company’s R&D team uses its combined industry knowledge of mineralogy, processing, manufacturing and chemistry to develop effective and cost efficient surface active agents and foaming dust suppressants.

“Surface active agents contain levels of sulphur, sodium and potassium, that if accelerated will alter a mineral’s chemistry and devalue quality, undermining end-user processes,” says Handel.

For example, elevated levels of these chemical elements reduce the quality of coal to the point that it is considered lower grade coal that is unsuitable for steel manufacturing, Handel notes.

There is a lot of pressure on companies that mine, transport and store coal to meet rigorous dust exposure standards, while continuing to supply high grade coal to steel manufacturers.

While reducing dust levels is a high priority, it is critical for companies to make sure the dust control solutions they are using are compatible with the type of material being mined, the dust control application systems and the intended manufacturing processes, says Handel

.

RST Solutions “specialises in solving complex dust issues” for mining and infrastructure projects globally with customised solutions adapted to varying factors such as mined materials and processes involved, local weather patterns, temperatures and land topography.

By considering a site’s application equipment and systems, as well as the upstream and downstream processes, RST Solutions develops advanced technologies tailored to solve site-specific issues caused by all types of fine particle matter from dust to mud, silt to sediment.

This expertise comes from over 30 years’ experience gained from developing solutions for extensive fine particle challenges presented by numerous industries, processes and material types.

Edited by Nadine James
Features Deputy Editor

Comments

The content you are trying to access is only available to subscribers.

If you are already a subscriber, you can Login Here.

If you are not a subscriber, you can subscribe now, by selecting one of the below options.

For more information or assistance, please contact us at subscriptions@creamermedia.co.za.

Option 1 (equivalent of R125 a month):

Receive a weekly copy of Creamer Media's Engineering News & Mining Weekly magazine
(print copy for those in South Africa and e-magazine for those outside of South Africa)
Receive daily email newsletters
Access to full search results
Access archive of magazine back copies
Access to Projects in Progress
Access to ONE Research Report of your choice in PDF format

Option 2 (equivalent of R375 a month):

All benefits from Option 1
PLUS
Access to Creamer Media's Research Channel Africa for ALL Research Reports, in PDF format, on various industrial and mining sectors including Electricity; Water; Energy Transition; Hydrogen; Roads, Rail and Ports; Coal; Gold; Platinum; Battery Metals; etc.

Already a subscriber?

Forgotten your password?

MAGAZINE & ONLINE

SUBSCRIBE

RESEARCH CHANNEL AFRICA

SUBSCRIBE

CORPORATE PACKAGES

CLICK FOR A QUOTATION